Water Heater Repair Jupiter FL's Blog

Jupiter Homeowner advice and maintenance tips for water heaters.

Water Heater T&P Valve Test

Explanations Why a Hot Water Tank Will Explode

When it comes to having to perform maintenance on ones water heater, it is a pretty minimal maintenance device. Even so, one critical aspect of it should be checked out routinely. Hot Water Heater Repair Jupiter FL wishes to pass on this safety information about ones water heater today.

Excessive temperature if coupled with tank deterioration inside the storage tank causes an explosion. Any time the water temperature is less than 212 degrees Fahrenheit, one will be safe from an explosion, though there is a associated risk of scalding at that temperature. But, if the water temperature is over 212 degrees, water becomes into steam, which will expand to 1,700 times the space it occupies as water. This is when an explosion can take place.

Cautionary Indications of a Water Heater Explosion
The leading sign is if one goes to get hot water from a faucet and only steam comes out. Quickly shut off electric power if one owns an electric water heater. If one owns a gas hot water heater, shut off the gas valve going to the water heater. Then, get in touch with us to come evaluate the condition.

Minimizing Potential Water Heater Dangers
The most essential maintenance task having a water heater is to examine the pressure relief valve, often known as the T&P valve, on a standard basis. This valve helps control the pressure buildup inside of the water storage tank to hinder a risky increase in temperature and overpressure.

Caution!
Be careful, the water release coming from a T&P valve is often really hot. If you do not feel comfortable evaluating the valve contact us. In addition, doing any kind of repairs to the valve ought to be done by a professional plumbing repair provider.

How to Test the T&P Valve

Remove anything from around the place around the overflow pipe and floor drain.
Raise the test handle for approximately 5 seconds or until the water runs clean.
Release the handle.
If the T&P valve keeps on running with water, lift the handle up and down rapidly to have it reseat itself. One might have to do so a couple of times. IF it has not been tested for a while, it might be difficult to raise it at first. Don’t use too much force, but may need to use just a little.
If the T&P valve continues to leak, it should really be replaced.
Additional things to watch out for are deterioration on the stem of the valve. If there is any water seeping from the valve stem or out of the drain valve.

Interested in far more strategies? Have a look at our additional articles here:

Water Heater Maintenance Infographic

Jupiter FL Water Heater Maintenance

Related T&P Valve Testing Videos

Mythbusters did a test of the potential dangers of hot water heater explosions here:

Water Heater T&P Valve Repair Jupiter FL

What the Experts Say

  • The discharge from a T&P valve can be very hot. It is very important that all T&P valves be installed properly with a discharge line piped downward to an adequate drain to avoid property damage and to minimize possible human contact.
    Read more…

Watts Water Technologies

If the temperature in your heater remains high after you turn down the thermostat, the thermostat may be faulty. Consult a professional for repair. Read more…

Home Guides

Pressure relief valves sometime develop a drip when opened for the first time in years. Try opening and closing it a few times to see if it will seat itself. If you have a large leak or the drip doesn’t stop on its own in a day or two, the valve will need to be replaced.  Read more…

Today's Homeowner

Check out some of our other water heater tips in our blog

Eliminating Water Heater Odors in Your Jupiter Home

Jupiter Water Heater Odor Repair

Are you experiencing an issue with smelly odors coming from the water originating from your water heater? It happens occasionally for a couple different reasons. Here is what Water Heater Repair Jupiter suggests to do to make sure your water smells much better and to remove any terrible taste fast.

Causes for Jupiter Water Heater Odors?

Bacteria entering into the water system is the most frequent factor ones water in the home may have smells. If you home utilizes well water or cities that utilize wells for the water source, raises the possibility of this developing.

With a water heater temperature level setting of 140 degrees or above will help in lowering the development of bacteria inside the water storage tank.

Ways to Eliminate Stinky Water Odors

The following directions discuss how you can use chlorine bleach to clean a water heater.

The electric or gas leading to the water heater tank has to first be shut off.

Next, the cold water supply off that leads to the tank needs to be shut off.

Open the hot water faucet of the kitchen sink to allow air to enter the tank.

With a a garden hose hooked up to the storage tank drain valve, drain the water inside the water heater.

Then close the drain valve once it is empty.

The next step is putting in the bleach.
If the hose for the cold water going into the storage tank is a flexible line, unscrew it from the tank. If not, one will have to remove the pressure relief valve, which is more involved. For electric water heaters, one of the elements can be removed.

Utilize a funnel to get bleach into the opening.
Add 5 ounces of bleach per gallon of the tank ability.
So if you have a 50 gallon water heater, you would need 250 ounces of bleach, or close to 2 gallons.

Re attached the water line or pressure relief valve.

Fill the tank back up with water once again.

Close the hot water faucet of the kitchen faucet as soon as all the air is out of the line.

Run all the hot water appliances until the odor of bleach is distinct. We want to get rid of the germs that can be found in the water lines also, not only inside the water heater.

Keep the water in the tank and water lines without using and hot water for 2 to 3 hours.

Drain the storage tank again and refill it. This time allow it to stay for at least 30 minutes and once more drain it.

Fill the tank back up. Open all of the hot water fixtures and let them run till the scent of bleach is gone.

For gas water heaters, relight the water heater pilot light. For electric water heaters, turn the power on again.

Additionally, by changing the anode rods, or maybe the type employed can work as the next video demonstrates:

Additionally, by replacing the anode rods, or perhaps the type employed can work as the next video shows:

Odors from Jupiter Water Heater

What the Experts Say

According to Soquel Creek Water District, “The smell is the result of four factors that must all be present for the odor to develop. These factors include:

  • A high concentration of sulfate in the raw water
  • Sulfate reducing bacteria, non-toxic to humans (sulfate is reduced to a sulfide state by the bacteria)
  • Little or no dissolved oxygen in the water
  • Hydrogen (a component of water which may be present due to water conditions reacting with the anode)”  Read more here…

Soquel Creek Water District

How is hydrogen sulfide gas produced in a water heater?

A water heater can provide an ideal environment for the conversion of sulfate to hydrogen sulfide gas. The water heater can produce hydrogen sulfide gas in two ways – creating a warm environment where sulfur bacteria can live, and sustaining a reaction between sulfate in the water and the water heater anode.  Read more…

Minnesota Department of Health

Check out some of our other water heater tips in our blog

Total Water Heater Maintenance Tips

Water Heater Repair Jupiter FL is not about to discuss the regrettable testimonies concerning water heater maintenance of “stumbling out of bed to the freezing bath,” here. Furthermore, we are going to presume that one is aware of the basic concept of making certain ones water heater is maintained routinely in an effort to receive the most from its expected life. This may help one reduce costs on energy costs as well. All of that is practical we realize. Though hot water heaters do not require a lot with regards to maintenance (and we are amazed, even though not shocked, by the quantity of customers we come across who have not carried out anything to their water heater), listed below are the duties people must understand relating to routine maintenance.

How Long Should My Jupiter FL Water Heater Last?

The standard gas water heater can last 8 to 10 years. There’s lots of things that may have an effect on the general lifetime needless to say, however this is an effective standard. In all probability the largest factor which will impact the long life of it is normally mineral deposits. A lot of of the tips in this article should go a long way in assisting to lower the accumulation of mineral deposits inside of the storage tank of the water heater.

Jupiter Water Heater Repair PreventionHot Water Heater Repair Jupiter FL

Property owners, even people which never feel excessively handy, are able to do plenty of water heater upkeep by themselves. However more often than not, water heaters are safe and sound, it is necessary to be aware of that they actually operate from electric power and/or gas, and so appropriate safety methods must be used. Be sure to make use of these techniques as an informative tutorial, for we’d much rather demonstrate all these together with you directly. The electric power to the water heater requires to be switched off ahead of working on any servicing. Ones breaker box ought to have a preferably labeled switch to point out which breaker is the heater’s. With a gas heater, turn the gas cutoff counterclockwise to switch off the gas to the device.

The section of the heater that aids with protecting against rusting inside of the water storage tank are the anode rods, or additionally labeled sacrificial anode rods. Many are composed of aluminum or magnesium around a steel wire. In time the external covering of the rods will erode and they need to be replaced when the steel wire is obvious. They ordinarily last around 5 years, though that could be reduced if ones water is soft. In the long term, it is better and less costly to have the anode rods changed, so that one can acquire an extended life from the water heater storage tank. The rods ought to be examined each year basis.

The follow video does a very good job of showing the method needed with replacing the anode rods:

Not every water heater has dip tubes. They must be looked at for deterioration every 6 months. To test it, take it out and check its length to the height of the water heater. It ought to be roughly 6″ to 8″ shorter as compared to the tank. Whenever it’s smaller than that, or simply exhibits symptoms of breakage or falling apart, it’ll need to get changed.

The big and small flush. Once again, mineral deposits are the primary reason of water heater malfunctions. Based on the level of quality of water in ones residence will establish just how rapidly sediment will build up inside of the storage tank. This sediment can solidify with time, bringing about peculiar popping sounds from the storage tank, lessen the effectiveness of the device, and perhaps clog up the drain valve. Ideally, every 6 months, but at the least every year, empty 1 or 2 gallons of water from the drain valve in the bottom of the hot water heater in a pail or by a hose in a container outdoors. Look to discover the amount of sediment is within the pail when the water settles. If it appears to be pretty clear, that great! When these types of small flushes are accomplished two times yearly, one may well not need to execute a big flush as frequently. If the water appears very dirty, a full flush needs to be completed. It is likewise a wonderful occasion to make certain the bottom drain valve of the storage tank is operating properly and not leaking. They are typically composed of plastic and after a while when they aren’t opened up, they may get stuck or not close up firmly, so opening and closing them in the course of the small flush test is very good.

There can be unique measures one may take through flushing to manage any sort of water smells which may arise when hot water comes from faucets within the house also.

This video exhibits exactly how and reasons behind a water heater flush:

Regarding holiday or temporary households, one ought to empty the storage tank of all its water in order to avoid any kind of flooding when the property is not being occupied. Of course, ensure to fill it up whenever the dwelling is to be resided in once again.

Water pipe inspection. Analyze to verify all water piping don’t have leaks or are impaired at all. It ought to be straightforward to see when there are any leaks coming from any piece of the water plumbing or storage tank for it will have water below and/or close to the device. Leaking water could potentially cause water damage to elements of ones household, so be sure that all seems dry, primarily if the heater is found within the residence and not in a garage.Jupiter Water Heater Repair

T&P valve evaluation. The T&P valve, also referred to as the temperature and pressure relief valve, should really be looked at annually. The function of the T&P valve would be to guard the water heater storage tank from surplus pressure, and exploding, not to frighten anybody. The owners guide must be looked over to ensure the appropriate methods are used but listed below are the standard actions. A little water can come out of the valve and it’s going to be really hot so be aware. Lift up the handle and let go of it. Have a container available to catch any unwanted water which could come out. Additionally, the noise of pressure getting discharged will be observed. The handle will need to snap back in position. In the event that it won’t give it a try once more. When it will not go back again into position following several attempts, it is going to have to be changed. The valve could possibly drip a little water after doing that for a little while. If it doesn’t quit dripping after a couple of hours inform us.

There does exist a great deal of discussion around what the finest temperature setting should really be. The manufacturer pre-programmed setting is normally 140 degrees, which is actually warmer than the majority of people may ever have to have. 120 degrees is the typical temperature and a number of people actually go as far as 100 degrees. We are publishing much more on this issue shortly, but we advise not going over 120 degrees.

Just For Gas Water HeatersWater Heater Repair Jupiter FL

The gas venting system requires being examined each 3 months. Take a look at to be sure all fittings are tight and for obstructions and deterioration to the vent pipes in addition to being confident that these are totally free of rust and deterioration .. Gas fired hot water heaters vent fumes to the outdoors of the residence. If these fumes flow inside of the house it might be fatal and a fire threat. Be sure that everything combustible or corrosive is faraway from the exhaust ventilation to prevent fires. Change all loose, broken or corroded areas of vent pipes.

Look at the pilot light to execute a visual examination of just how it is working. The pilot light is the element that ignites the gas burner that will heat the water. A clean burning and correctly adjusted pilot light is necessary for your water heater to function at peak efficiency. The color of the flame of the pilot light really should be blue with natural gas heaters or blue/green with just a bit of yellow at the tip with propane heaters. A weakened flame, a yellow flame, or a flame which has a divided flame on the top signifies that a modification is required.

Just For Electric Water Heaters

Making use of insulation wraps or covers around the storage tank can certainly help preserve a regular temperature inside of the storage tank without the need for as much electric power. In addition, with the heater not needing to operate as much will increase the life span of the heating element given that it will not be utilised as much. Every 3 months roughly, verify to guarantee the insulation cover is attached properly and hasn’t fallen or shifted on the water storage tank.

Routine evaluation of the heating element is significant and definitely will help minimize the need for an unexpected emergency repair. We aren’t going to get into the specifics for a complete assessment right here, however one will require a voltage/OHM meter to verify there exists a closed electrical circuit. Heating elements will need changing from time to time.

Continue to keep the vicinity close to ones water heater thoroughly clean of dirt. Specifically if the water heater is found in the garage area, be certain to keep the place swept. The cleaner the heater is, the considerably better it is going to run without having the requirement of a water heater repair.

Replace Old Water Heaters With Energy Efficient Ones

Today, virtually all water heaters made have got a good quantity of energy efficiency. In April of 2015, new rules were set up in the United States on water heaters. Certainly, the better the heater, the longer the life one is certain to get from the device using the right upkeep through the years. Don’t wait to phone Hot Water Heater Repair Jupiter FL to talk about water heater maintenance or perhaps to help answer any concerns on picking the most suitable replacement water heater for ones house or workplace. Brand, model, and size must all be considered in the course of the selection process and not merely utilize the “bigger the better” slogan. With regard to storage tank water heaters, one doesn’t desire to be continuously preserving a surplus quantity of hot water that won’t be used.

How Healthy Is Your Water Heater

Most people don’t ever consider the state of the property’s water heater Water Heater Repair Jupiter FL knows. Rightfully so, provided that it is working properly. Nonetheless, a little water heater upkeep can go a long way toward minimizing the number and frequency of repairs, and in fact assists to lengthen the life of the heater, staying clear of very early replacement. Find out exactly how keeping your water heater can impact its life expectancy and offer you less stunning minutes of cold water.

A Healthy Water HeaterHot Water Heater Repair Jupiter FL

While it is difficult to figure out specifically how long a water heater need to last, an effectively serviced, quality water heater can last 8 to 10 years. Naturally, lots of aspects will influence the life-span, consisting of electrical energy abnormalities, the quality of the water heater, and the mineral density of the water. Routine water heater service can likewise minimize electric costs by helping it operate more efficiently

Among wears out a water heater are mineral deposits. A great deal of cash is invested changing heating elements and entire tanks, when a little upkeep periodically would assist to prevent this expenditure from happening. A healthy water heater is one that is insulated, clean, and without electrical wiring faults.

Troubles with ones water heater usually end up being self-evident: A hot water faucet is not able to bring hot water, there are leaks or puddles near the water heater, or the tank releases odd gurgling or popping noises. These are a couple of signs informing you when your hot water heater requires changing.

It would be great to understand prior to your water heater has a leakage and triggers a trouble or even worse yet damage to the house. If you identify you have a few of the very early caution indicators you will have time to examine your selections of sizes and versions and pick a certified installer as opposed to hurrying to discover a replacement water heater on a Friday afternoon or even worse on a weekend.

Below are some indications that you might need a a brand-new hot water heater:

Age: Typically, a gas hot water heater ought to last anywhere in between 8 to 12 years, while an electric version will last a bit longer at 10 to 15 years.
Stained Water: When you utilize your hot water tap, does the water look a bit colored? If so, there could be rust in the water heater, which is a possible indication the hot water heater is revealing indicators of wear and might begin to leak.
Banging or Popping: When there is a accumulation of hard water sediment in the water heater,it might could sound like explosions. These sounds are triggered by the difference in water temperature inside the tank as new cold water mixes with the heated water of the tank.
Moisture: Look around the base of the water heater for wetness, for this could be a sign of a slow-moving or periodic leakage.
Cold Water: An unanticipated cold shower is not just bad means to begin your day, however of a hot water heater that has to be taken a look at.
Significant Water Leaks: It’s time to call Hot Water Heater Repair Jupiter FL now.

Springtime Plumbing Maintenance Duties

Springtime is a pleasurable period of the year certainly, but it does bring with it various duties for property owners. Water Heater Repair Jupiter FL wishes to discuss some upkeep jobs to do around your house to make sure ones plumbing and other systems are working as well as possible. The majority of these tasks will not take long to do and will assist rather a little bit in maintaining the value of ones house, along with making it more energy reliable.

Water HeaterWater Heater Repair Jupiter FL
The average life of a water heater is from 8 to twelve years. It’s recommended to inspect to determine if one can find any leaks or rust appearing at the device’s base, and if there are any water leaks because of rust, it is a very good sign that the water heater will need to be replaced sadly. If your house has hard water, it might be needed to drain the water heater to eliminate deposit buildup in the tank. This must be done two times a year to maintain the heater working successfully. It additionally helps make it perform quieter also!

Plumbing
If one notices any leaking water fixtures, change washers as required, regardless if your feline enjoys to sit in the bath tub and lick the leakage. And do not forget to examine for under-sink and dishwasher leakages and repair as needed. When it’s spring and not warm enough to sweat engaging in these duties, ensure the water pipes aren’t also. Furthermore make certain drains are running easily and the washing machine hoses are not protruding, split, or damp. Nobody wishes for water destruction from a significantly leaking clothes washer!

Outdoor Faucets
Turn all outside water fixtures back on…ideally they happen to be turned off in the late fall months. At the same time test for any leaks from them and lawn hoses.

Refrigerators
The refrigerator is among the greatest electrical energy eaters in the household, so making certain that the door seals are tight is necessary. To check this, shut the door on a dollar bill and in case it can quickly drawn away, the door latch could require a readjustment or the seal might require being changed. Amazingly, a small little bit of air loss can lead to greater energy costs. And it’s likewise an excellent time to clean out the back coils as that is an additional reason for inadequacy.

Storm Windows and Screens
The radical modifications in temperature level in between the winter season and early spring can damage caulking or rubber seals all around a house’s windows and exterior doors. Devote some time and examine them. It is actually a simple repair and the energy expenses will show the time devoted. Any detachable storm windows can be taken down, washed, and exchanged with window screens. And, always remember to repair holes in windows and door screens to shut out mosquitoes and various other small pests.

AC Units
Examine portable AC systems to see to it they are operating and filters are replaced. The warm climate will come faster than one generally believes. An AC not just cools you down, however a reliable AC minimizes humidity from the residence, which can in fact harm the foundation if left uncontrolled. Enter the routine of altering or cleaning the filters of both a main system and portable devices once a month as dust and dirt minimizes effectiveness. It si important for central AC systems that the hose connections are not leaky and the drain pans are draining appropriately. If a condensate drain line ends up being obstructed, it could be a buildup of algae. If this holds true, make use of a wet-vac to pull out any clog. And as well, clear out the ducts too.

Hot Water Heater Repair Jupiter FL hopes these chores are handy and will be incorporated in with your to-do lists! Look at some of our additional water heater recommendations here:

Water Heater Troubleshooting Pointers

Water Heater Troubleshooting Pointers

A hot water heater is a hard working appliance. Day or evening, it’s creating completely heated water whenever you desire it. So when it unexpectedly is no longer working correctly, many of us have the tendency to worry.

Luckily a nonfunctioning water heater does not constantly indicate a pricey repair work. Prior to making an emergency call to Water Heater Repair Jupiter FL, we recommend examining the trouble yourself first.

Jupiter Water Heater Repair Troubleshooting

Check the Pilot Light

For a gas water heater, get rid of the small panel on the bottom of the appliance and look to notice if the pilot light is ignited.
Spark it with a match or lighter to re-ignite it. If it remains lit, the water heater must kick-in and begin operating appropriately.
If the pilot burner on the water heater does not remain ignited, you could have to change the thermocouple or have the burner cleaned.

Replace the ThermocoupleHot Water Heater Repair Jupiter FL

It seems like part of a space ship, however it’s in fact a basic gadget that you can change on your water heater.

Check the owner’s guide. It must have guidelines for the best ways to get rid of and change the thermocouple.
Switch off the gas prior to taking out anything at all from the water heater.
Using the guidelines in your individual’s guide, get rid of the thermocouple by separating it from both sides of the aviator line.
Change the thermocouple on the water heater with a brand-new one that is cut to length.
Turn on the gas and check for leakages, then re-light the pilot light.

Hit the Reset Button

If you have an electric water heater, find the reset button and push it till you hear a click.
If you do not hear a click, or it falls short to reboot the water heater, reset the breaker.
If a breaker reset does not suffice, you could have to change the thermostat.

Change the Thermostat

Shut down the power to the water heater, and turn off the breaker it is linked to. You do not wish to electrocute yourself!
Use the owner’s guide to find the thermostat wires, then separate them.
Get rid of the thermostat and have it checked by a device dealership. If it is malfunctioning, change it.

Change the Heating Element

With the power still turned off, get rid of the gain access to panel on the water heater.
Loosen the terminal screws and pull the wires far from the heating element.
Get rid of each part of the element and have them checked by a device repair shop. If they are malfunctioning, change them.

Your water heater must be working in no time. If these actions fall short to repair your hot water heater, or if you do not feel relaxed doing them by yourself, call Hot Water Heater Repair Jupiter FL.

Jupiter Water Heater Repair Company Video

We absolutely love the things we do here at Water Heater Repair Jupiter FL and look forward to assisting as many of our Jupiter community as possible. We will continue to provide guidance on water heater maintenance right here in this blog too.

We would like to share our brand new company introduction video to you below.

We are in addition accessible to assist you with every other kind of plumbing repair you may need completed. Whether a leaking faucet, drain cleaning, toilet repair, or leak detection. We have witnessed practically any sort of emergency plumbing and water heater repair circumstance you can envision and look forward to employing our well crafted troubleshooting abilities!

If you are imagining it is becoming near requiring a water heater replacement inform us as well, for we will do all we can to help support you in that scenario.